Example 1: Design and Analyze a Corrugated Horn in the Band from 10 to 20 GHz

This case explains how to calculate far-field, radiation pattern, current density, charge density and near field of a corrugated horn.

Step 1: Create a new MOM Project.

Open newFASANT and select 'File --> New' option.



Figure 1. New Project panel

Select MOM option on the previous figure and start to configure the project.

Step 2: Change the scale to millimeters.



Figure 2. Scale settings

Step 3: Create the geometry of the corrugated horn.

Execute the function “ corrugated_horn(fmin,fmax)” (which can be downloaded). To execute the function, click on Tools - Calculator and write the call to the function.



Figure 3. Calculator panel
The parameters to set are:
  • fmin is the lowest operating frequency (GHz)
  • fmax is the highest operating frequency (GHz)

The script file, called script_corrugated_horn.nfs, will be automatically generated in the mydatafiles folder in the newFASANT directory.

The next step is to execute the generated script file. For that, click on Tools – Script - Load and open the script “ script_corrugated_horn.nfs”.



Figure 4. Horn geometry has been generated.

Step 4: Set Simulation Parameters.

Select 'Simulation --> Parameters' option on the menu bar and the following panel appears. Set the parameters as the next figure shows and save it.



Figure 5. Simulation Parameters panel

Step 5: Set the source parameters.

Select 'Source --> Dipole --> Dipole Antenna' option and set the parameters as show the next figure. Then save the parameters and the dipole appears.



Figure 6. Dipole Antenna panel

Select 2 electric dipoles and click on “Position”.



Figure 7. Electric Dipole 1 Settings


Figure 8. Electric Dipole 2 Settings

Step 6: Set the solver parameters.

Click on Solver --> Parameters option on the menu bar. Verify that all the parameters are defined by default, as shown in next figure. Click on Save button before going to next step.



Figure 9. Solver panel

Select ‘Advanced Options’ and activate Preconditioner as shown.



Figure 10. Preconditioner panel

Step 7: Meshing the geometry model.

Select 'Meshing --> Parameters' to open the meshing configuration panel and then set the parameters as show the next figure. In order to obtain the shortest possible time for meshing, it is recommended to run the process of meshing with the number of physical processors available to the machine.



Figure 11. Meshing panel
The user can choose between:
  • octaves an automatic frequency range per octave is performed, that depends on the Initial and Final frequency. The user can choose 1 frequency by an octave or several frequencies by an octave. The more frequencies per octave, the greater the precision
  • all frequencies a meshing by each frequency is built, so it is the more accurate option. This option will only be chosen when the user needs a very accurate mesh.

Step 8: Execute the simulation.

Select 'Calculate --> Execute' option to open simulation parameters. Then select the number of processors as the next figure show. In order to obtain the shortest possible time for calculating the results, it is recommended to run the process with the number of physical processors available to the machine.



Figure 12. Execute panel

Then click on 'Execute' button to starting the simulation.

Step 9: Show Results.

To get more information about the graphics panel advanced options (clicking on right button of the mouse over the panel) see Annex 1: Graphics Advanced Options.

Select 'Show Results --> Far Field --> View Cuts' option to show the cuts of the observation directions options.



Figure 13. Far Field cuts - Linear Amplitude

Selecting other values for the component, step, frequency or cut parameters and clicking on 'Add Series' button a new cut will be added to the selected parameters.

On 'Show Results --> Far Field' menu, other results are present such as 'View Cuts by Step' and 'View Cuts by Frequency' and this option display the values for one selected point for each step or frequency.

On 'Show Results --> Radiation Pattern' menu, other results are present such as 'View Cuts by Step' and 'View Cuts by Frequency' and this option display the values for one selected point for each step or frequency.

Select 'Show Results --> Radiation Pattern --> View 3D Pattern' option to show the cuts of the radiation pattern options.



Figure 14. Radiation Pattern 3D

Changing values for step, frequency, component or filtering parameters the visualization for the new parameters will be shown.

Select 'Show Results --> View Currents' option to show the current density.



Figure 15. Current Density

Changing values for step, frequency, magnitude, component or filtering parameters the visualization for the new parameters will be shown.

Select 'Show Results --> View Charges' option to show the charge density.



Figure 16. Charge Density

Changing values for step, frequency, magnitude or filtering parameters the visualization for the new parameters will be shown.

On 'Show Results --> Far Field' menu, other results are present such as 'View Cuts by Step' and 'View Cuts by Frequency' and this option display the values for one selected point for each step or frequency.