モデルの作成
CADFEKOでモデルを作成します。このモデルに必要なポートと給電源をすべて定義します。このモデルの動作周波数または動作周波数範囲を指定します。
- モデルの寸法単位をミリメートルに設定します。
-
次の変数を定義します:
- d = 5.8(周期的境界条件の間隔)
- h = 0.5(基板の厚み)
- t = 0.091(接着剤の厚み)
- s1 = 0.15(誘電体下層の幅)
- s2 = 0.18(誘電体上層の幅)
- w = 2.5(金属板の幅)
- fmin = 5e9(最小周波数)
- fmax = 15e9(最大周波数)
-
誘電体の2つの層を作成します。
-
原点を中心とした下層の立方体を作成します。
- Definition method: Base centre, width, depth, height
- Base centre:(0, 0, 0)
- Width: d
- Depth: d
- Height: h
- Label: LowerLayer
-
中間層の立方体を作成します。
- Definition method: Base centre, width, depth, height
- Base centre:(0, 0, h)
- Width: d
- Depth: d
- Height: t
- Label: Glue
-
上位層の立方体を作成します。
- Definition method: Base centre, width, depth, height
- Base centre: (0, 0, h + t)
- Width: d
- Depth: d
- Height: h
- Label: UpperLayer
-
原点を中心とした下層の立方体を作成します。
-
下部と上部のPECサーフェスを作成します。
-
上部長方形を作成します。
- Definition method: Base centre, width, depth
- Base centre: (0, 0, h + t + h)
- Width: d-s1
- Depth: d-s1
- Label: S1
-
下部長方形を作成します。
- Definition method: Base centre, width, depth
- Base centre:(0, 0, 0)
- Width: d - s2
- Depth: d - s2
- Label: S2
-
上部長方形を作成します。
-
接着剤にPECサーフェスのアウトラインを作成します。
-
長方形を作成します。
- Definition method: Base centre, width, depth
- Base centre:(0, 0, h + t)
- Width: d
- Depth: w
- Label: L1
-
長方形を作成します。
- Definition method: Base centre, width, depth
- Base centre:(0, 0, h + t)
- Width: w
- Depth: d
- Label: L2
-
長方形を作成します。
- パートL1およびL2を結合します。
- Union1にSimplify変換を使用して、2つの長方形の重なりによって生じる不要なエッジを削除します。
- すべてのパートを結合します。
-
2つの誘電体媒質を作成します。
-
誘電体媒質Substrateを作成します。
- Relative permittivity: 3.38
- Dielectric loss tangent: 0
- Label: Substrate
-
誘電体媒質Glueを作成します。
- Relative permittivity: 3.3
- Dielectric loss tangent: 0
- Label: Glue
-
誘電体媒質Substrateを作成します。
-
2つの層の領域特性を設定します
- 誘電体中央層の領域をGlueに設定します。
- 残りの2つの層の領域をSubstrateに設定します。
-
Glue材料の上部に中心を置いたフェイスをPECに設定します。
-
上部と下部の大きいフェイスをPECに設定し、残りの狭い面(大きな上面とそれに対応した下面の境界)は、DefaultまたはDielectric
boundaryに設定します。
- θ=0°およびϕ=0°として単一の入射平面波を追加します。
- fminからfmaxまで連続した周波数範囲を設定します。
-
2つの主平面を対称面とした対称性を指定します:
- X=0: Geometric symmetry
- Y=0: Geometric symmetry
Note: 周期境界条件では幾何学的な対称性のみがサポートされます。