EIM - IMPOSEREGIONS

Magnitude of direction vector A for PARALLELEPIPEDVEL impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedvel_A_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in A direction for PARALLELEPIPEDVEL impose region #1 must be non-negative.

The side length defined in "parallelepipedvel_A_len" is a negative number. The length must be zero or positive.

Magnitude of direction vector B for PARALLELEPIPEDVEL impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedvel_B_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in B direction for PARALLELEPIPEDVEL impose region #1 must be non-negative.

The side length defined in "parallelepipedvel_B_len" is a negative number. The length must be zero or positive.

Magnitude of direction vector C for PARALLELEPIPEDVEL impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedvel_C_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in C direction for PARALLELEPIPEDVEL impose region #1 must be non-negative.

The side length defined in "parallelepipedvel_C_len" is a negative number. The length must be zero or positive.

Vectors A, B, and C defined for PARALLELEPIPEDVEL impose region #1 generate no volume, and will not have effect.

The vectors defining the parallelepiped are coplanar, so no volume is generated and the region will not have effect.

The phase number requested for impose region #1 to move with is either non-positive or larger than the total number of phases.

The impose region motion phase "imposeregion_motphs" must be positive and no larger than the total number of phases defined in "phases" section.

The phase requested for impose region #1 to move with is not a moving wall.

The impose region motion phase "imposeregion_motphs" must point to a MOVINGWALL phase from the "phases" section.

Direction vector magnitude for a PARALLELEPIPEDVEL impose region is too small.

The magnitude of vector defined in "parallelepipedvel_unv" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Axis vector magnitude for CYLINDERVEL impose region #1 is too small.

The magnitude of normal vector defined in "cylindervel_axis" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

The height of CYLINDERVEL impose region #1 must be non-negative.

The height of cylinder defined in "cylindervel_hght" is a negative number. The height must be zero or positive.

The radius of CYLINDERVEL impose region #1 is negative.

The radius of a CYLINDERVEL impose region specified in "cylindervel_rad" must be non-negative.

The phase number requested for impose region #1 to move with is either non-positive or larger than the total number of phases.

The impose region motion phase "imposeregion_motphs" must be positive and no larger than the total number of phases defined in "phases" section.

The phase requested for impose region #1 to move with is not a moving wall.

The impose region motion phase "imposeregion_motphs" must point to a MOVINGWALL phase from the "phases" section.

Velocity direction vector for CYLINDERDVEL impose region #1 is too small.

The magnitude of velocity direction vector defined in "cylindervel_unv" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Magnitude of direction vector A for PARALLELEPIPEDACC impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedacc_A_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in A direction for PARALLELEPIPEDACC impose region #1 must be non-negative.

The side length defined in "parallelepipedacc_A_len" is a negative number. The length must be zero or positive.

Magnitude of direction vector B for PARALLELEPIPEDACC impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedacc_B_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in B direction for PARALLELEPIPEDACC impose region #1 must be non-negative.

The side length defined in "parallelepipedacc_B_len" is a negative number. The length must be zero or positive.

Magnitude of direction vector C for PARALLELEPIPEDACC impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedacc_C_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in C direction for PARALLELEPIPEDACC impose region #1 must be non-negative.

The side length defined in "parallelepipedacc_C_len" is a negative number. The length must be zero or positive.

Vectors A, B, and C defined for PARALLELEPIPEDACC impose region #1 generate no volume, and will not have effect.

The vectors defining the parallelepiped are coplanar, so no volume is generated and the region will not have effect.

The phase number requested for impose region #1 to move with is either non-positive or larger than the total number of phases.

The impose region motion phase "imposeregion_motphs" must be positive and no larger than the total number of phases defined in "phases" section.

The phase requested for impose region #1 to move with is not a moving wall.

The impose region motion phase "imposeregion_motphs" must point to a MOVINGWALL phase from the "phases" section.

Direction vector magnitude for a PARALLELEPIPEDACC impose region is too small.

The magnitude of unit vector defined in "parallelepipedacc_unv" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Normal vector magnitude for CYLINDERACC impose region #1 is too small.

The magnitude of vector defined in "cylinderacc_axis" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

The height of CYLINDERACC impose region #1 must be non-negative.

The height of cylinder defined in "cylinderacc_hght" is a negative number. The height must be zero or positive.

The radius of CYLINDERACC impose region #1 must be non-negative.

The radius of a CYLINDERACC impose region specified in "cylinderacc_rad" is a negative number. The radius must be zero or positive.

The phase number requested for impose region #1 to move with is either non-positive or larger than the total number of phases.

The impose region motion phase "imposeregion_motphs" must be positive and no larger than the total number of phases defined in "phases" section.

The phase requested for impose region #1 to move with is not a moving wall.

The impose region motion phase "imposeregion_motphs" must point to a MOVINGWALL phase from the "phases" section.

Direction vector magnitude for a CYLINDERACC impose region is too small.

The magnitude of vector defined in "cylinderacc_unv" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Magnitude of direction vector A for PARALLELEPIPEDTEMP impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedtemp_A_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in A direction for PARALLELEPIPEDTEMP impose region #1 must be non-negative.

The side length defined in "parallelepipedtemp_A_len" is a negative number. The length must be zero or positive.

Magnitude of direction vector B for PARALLELEPIPEDTEMP impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedtemp_B_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in B direction for PARALLELEPIPEDTEMP impose region #1 must be non-negative.

The side length defined in "parallelepipedtemp_B_len" is a negative number. The length must be zero or positive.

Magnitude of direction vector C for PARALLELEPIPEDTEMP impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedtemp_C_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in C direction for PARALLELEPIPEDTEMP impose region #1 must be non-negative.

The side length defined in "parallelepipedtemp_C_len" is a negative number. The length must be zero or positive.

Vectors A, B, and C defined for PARALLELEPIPEDTEMP impose region #1 generate no volume, and will not have effect.

The vectors defining the parallelepiped are coplanar, so no volume is generated and the region will not have effect.

The phase number requested for impose region #1 to move with is either non-positive or larger than the total number of phases.

The impose region motion phase "imposeregion_motphs" must be positive and no larger than the total number of phases defined in "phases" section.

The phase requested for impose region #1 to move with is not a moving wall.

The impose region motion phase "imposeregion_motphs" must point to a MOVINGWALL phase from the "phases" section.

Normal vector magnitude for CYLINDERTEMP impose region #1 is too small.

The magnitude of normal vector defined in "cylindertemp_axis" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

The height of CYLINDERTEMP impose region #1 must be non-negative.

The height of cylinder defined in "cylindertemp_hght" is a negative number. The height must be zero or positive.

The radius of CYLINDERTEMP impose region #1 must be non-negative.

The radius of a CYLINDERTEMP impose region specified in "cylindertemp_rad" is a negative number. The radius must be zero or positive.

The phase number requested for impose region #1 to move with is either non-positive or larger than the total number of phases.

The impose region motion phase "imposeregion_motphs" must be positive and no larger than the total number of phases defined in "phases" section.

The phase requested for impose region #1 to move with is not a moving wall.

The impose region motion phase "imposeregion_motphs" must point to a MOVINGWALL phase from the "phases" section.

Magnitude of direction vector A for PARALLELEPIPEDPOROUS impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedporous_A_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in U direction for PARALLELEPIPEDPOROUS impose region #1 must be non-negative.

The side length defined in "parallelepipedporous_A_len" is a negative number. The length must be zero or positive.

Magnitude of direction vector B for PARALLELEPIPEDPOROUS impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedporous_B_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in B direction for PARALLELEPIPEDPOROUS impose region #1 must be non-negative.

The side length defined in "parallelepipedporous_B_len" is a negative number. The length must be zero or positive.

Magnitude of direction vector C for PARALLELEPIPEDPOROUS impose region #1 is too small.

The magnitude of direction vector defined in "parallelepipedporous_C_vec" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

Length in C direction for PARALLELEPIPEDPOROUS impose region #1 must be non-negative.

The side length defined in "parallelepipedporous_C_len" is a negative number. The length must be zero or positive.

Vectors A, B, and C defined for PARALLELEPIPEDPOROUS impose region #1 generate no volume, and will not have effect.

The vectors defining the parallelepiped are coplanar, so no volume is generated and the region will not have effect.

The phase number requested for impose region #1 to move with is either non-positive or larger than the total number of phases.

The impose region motion phase "imposeregion_motphs" must be positive and no larger than the total number of phases defined in "phases" section.

The phase requested for impose region #1 to move with is not a moving wall.

The impose region motion phase "imposeregion_motphs" must point to a MOVINGWALL phase from the "phases" section.

At least two of the "porous_principal_ax_x_i", "porous_principal_ax_y_i" and "porous_principal_ax_z_i" for phase #1 should be defined.

If new axes of for the porous region were to be defined, at least two of the keywords "porous_principal_ax_x_i", "porous_principal_ax_y_i" or "porous_principal_ax_z_i" must appear in a PARALLELEPIPEDPOROUS Region definition. There is no need to define the principal axes if they are parallel to the global xyz axes. Typographical errors may also lead to this message.

"porous_principal_ax_x_i" defined for region #1 has zero length.

The keyword "porous_principal_ax_x_i" of a PARALLELEPIPEDPOROUS motion is either not defined or has zero magnitude. Typographical errors may also lead to this message.

"porous_principal_ax_y_i" defined for region #1 has zero length.

The keyword "porous_principal_ax_y_i" of a PARALLELEPIPEDPOROUS motion is either not defined or has zero magnitude. Typographical errors may also lead to this message.

"porous_principal_ax_z_i" defined for region #1 has zero length.

The keyword "porous_principal_ax_z_i" of a PARALLELEPIPEDPOROUS motion is either not defined or has zero magnitude. Typographical errors may also lead to this message.

"porous_principal_ax_x_i" and "porous_principal_ax_y_i" defined for phase #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_x_i" and "porous_principal_ax_y_i" of a PARALLELEPIPEDPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_x_i" and "porous_principal_ax_z_i" defined for region #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_x_i" and "porous_principal_ax_z_i" of a PARALLELEPIPEDPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_y_i" and "porous_principal_ax_z_i" defined for region #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_y_i" and "porous_principal_ax_z_i" of a PARALLELEPIPEDPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_x_i" and "porous_principal_ax_y_i" defined for region #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_x_i" and "porous_principal_ax_y_i" of a PARALLELEPIPEDPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_x_i" and "porous_principal_ax_z_i" defined for region #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_x_i" and "porous_principal_ax_z_i" of a PARALLELEPIPEDPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_y_i" and "porous_principal_ax_z_i" defined for region #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_y_i" and "porous_principal_ax_z_i" of a PARALLELEPIPEDPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_x_i", "porous_principal_ax_y_i" and "porous_principal_ax_z_i" defined for region #1 do not follow the right hand rule.

The difference of the cross product of vectors "porous_principal_ax_x_i", "porous_principal_ax_y_i" and "porous_principal_ax_z_i" of a PARALLELEPIPEDPOROUS motion and 1 is larger than 1.0e-6.

Normal vector magnitude for CYLINDERPOROUS impose region #1 is too small.

The magnitude of normal vector defined in "cylinderporous_axis" is smaller than 1.0e-6. This error may be due to missing keywords or typographical mistakes.

The height of CYLINDERPOROUS impose region #1 must be non-negative.

The height of cylinder defined in "cylinderporous_hght" is a negative number. The height must be zero or positive.

The radius of CYLINDERPOROUS impose region #1 must be non-negative.

The radius of a CYLINDERPOROUS impose region specified in "cylinderporous_rad" is a negative number. The radius must be zero or positive.

The phase number requested for impose region #1 to move with is either non-positive or larger than the total number of phases.

The impose region motion phase "imposeregion_motphs" must be positive and no larger than the total number of phases defined in "phases" section.

The phase requested for impose region #1 to move with is not a moving wall.

The impose region motion phase "imposeregion_motphs" must point to a MOVINGWALL phase from the "phases" section.

At least two of the "porous_principal_ax_x_i", "porous_principal_ax_y_i" and "porous_principal_ax_z_i" for phase #1 should be defined.

If new axes of for the porous region were to be defined, at least two of the keywords "porous_principal_ax_x_i", "porous_principal_ax_y_i" or "porous_principal_ax_z_i" must appear in a CYLINDERPOROUS Region definition. There is no need to define the principal axes if they are parallel to the global xyz axes. Typographical errors may also lead to this message.

"porous_principal_ax_x_i" defined for region #1 has zero length.

The keyword "porous_principal_ax_x_i" of a CYLINDERPOROUS motion is either not defined or has zero magnitude. Typographical errors may also lead to this message.

"porous_principal_ax_y_i" defined for region #1 has zero length.

The keyword "porous_principal_ax_y_i" of a CYLINDERPOROUS motion is either not defined or has zero magnitude. Typographical errors may also lead to this message.

"porous_principal_ax_z_i" defined for region #1 has zero length.

The keyword "porous_principal_ax_z_i" of a CYLINDERPOROUS motion is either not defined or has zero magnitude. Typographical errors may also lead to this message.

"porous_principal_ax_x_i" and "porous_principal_ax_y_i" defined for phase #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_x_i" and "porous_principal_ax_y_i" of a CYLINDERPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_x_i" and "porous_principal_ax_z_i" defined for region #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_x_i" and "porous_principal_ax_z_i" of a CYLINDERPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_y_i" and "porous_principal_ax_z_i" defined for region #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_y_i" and "porous_principal_ax_z_i" of a CYLINDERPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_x_i" and "porous_principal_ax_y_i" defined for region #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_x_i" and "porous_principal_ax_y_i" of a CYLINDERPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_x_i" and "porous_principal_ax_z_i" defined for region #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_x_i" and "porous_principal_ax_z_i" of a CYLINDERPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_y_i" and "porous_principal_ax_z_i" defined for region #1 are not perpendicular.

The dot product of vectors "porous_principal_ax_y_i" and "porous_principal_ax_z_i" of a CYLINDERPOROUS motion is larger than 1.0e-6.

"porous_principal_ax_x_i", "porous_principal_ax_y_i" and "porous_principal_ax_z_i" defined for region #1 do not follow the right hand rule.

The difference of the cross product of vectors "porous_principal_ax_x_i", "porous_principal_ax_y_i" and "porous_principal_ax_z_i" of a CYLINDERPOROUS motion and 1 is larger than 1.0e-6.